Cisco: How to configure HSRP

In this post I proposed to discuss a little bit about Hot Standby Router Protocol and how it can be configured on a Cisco device. For this I have chosen the following topology:

cisco-configure-hsrp

I had in mind this scenario due to the fact that the traffic can take multiple paths in case of link being down and this give us the possibility to have a little bit of conversation on HSRP topic.
HSRP is defined in the document RFC2281 and according to the definition in this document: “The Hot Standby Router Protocol, HSRP, provides a mechanism which is designed to support non-disruptive failover of IP traffic in certain circumstances.” If you want to read more about the details how HSRP is working, please the RFC2281. I think there is not point in reproducing here what is already written there.
Regarding our topology, what you should know is that after configuring HSRP on R1 and R2 we will achieve a failover mechanism for the traffic from the Client (192.168.0.10) to the Server(10.10.10.10). From the beginning we will assume that R1 and R2 have the proper routing already configured to reach this destinations.

In the below presentation, you will see how the failover is achieved and what’s happening when you have a proper HSRP configuration in case that the link SC – R1 is broken:

So, how to achieve this behavior? From the topology you notice that proper configuration of HSRP involves 3 IP addresses from the same subnet (in our case this is 192.168.0.0 /24). One of the IP is configured on R1 the second one on R2 and the third one is HSRP IP address, which will be announced to the Client as gateway.

Configuration is straight forward on R1:

configure terminal
interface fa0/0
ip address 192.168.0.1 255.255.255.0
standby 1 ip 192.168.0.254
standby 1 priority 110

and on R2:

configure terminal
interface fa0/0
ip address 192.168.0.2 255.255.255.0
standby 1 ip 192.168.0.254

First we configure an IP address on the interface. Then we configure HSRP by typing the command “standby” followed by HSRP group (in our case group 1) and then the IP address. HSRP default priority is 100, and the principle is the higher the better. To force the path R1-SC to be the preferred one, we increse the priority to 110, making R1 to be the “Active” one. The other router, in our case R2, will have the HSRP status “Standby“. Maybe you are wondering what happens if you don’t configure the priority and both routers are having the same value 100. In this case HSRP has a mechanism that help it to chose the active router by comparing the IP addresses and chosing the one with the higher value. In our case this would be R2 (192.168.0.2 > 192.168.0.1).
Another useful feature that I recommend to configure for HSRP is “preemption“. The HSRP preemption feature enables the router with highest priority to immediately become the Active router. The configuration is also very simple and inquire only one additional line to the above ones:

standby 1 preempt

Also recommended is to configure “authentication“ between the HSRP participants:

standby 1 authentication somepassword

where “somepassword” can be what ever you want.

Going back to the topology, another scenario can take place. What if the link R1 – SC remains active, and instead the R1 – SS goes down. Since the R1 – SC is UP, the router R1 has no intention to cease the HSRP Active status. If you are having some kind of dynamic routing between R1 and R2, then you are on the safe side as the traffic will flow like in the scenario below (I’m assuming R1 to be the Active one for both R1-SC and R1-SS):

Remember that if do not have some routing between R1 and R2, the packets will be dropped on R1 as they will not have any path to the Server IP address 10.10.10.10.

This situation can be avoid with another HSRP feature, that will force the R1 to change it’s status from Active to Standby by monitoring the interface from R1 to SS. This feature is called “interface tracking“. This HSRP feature you have to configure at least on the router which is usual in Active mode:

standby 1 track FastEthernet1/0 30

In this scenario I assume that interface Fa1/0 is the connection to SS switch. This tracking command is watching for the status on the interface Fa1/0. When it’s status changes to “down” the “priority” value (110 in this example) is decremented with 30 (or whatever you will configure in the command line). After decremental, the “priority”
will have a value of 80 which is lower than the default one (100), forcing R2 to become the Active router and changing the R1 status to Standby.

Checking the status of an HSRP participant is very easy, and you can see this in the output below:

R1#show standby brief
P indicates configured to preempt.
|
Interface   Grp Prio P State    Active          Standby         Virtual IP
Fa0/0       1   110  P Active   local           192.168.0.2   192.168.0.254

R2#show standby brief
P indicates configured to preempt.
|
Interface   Grp Prio P State    Active          Standby         Virtual IP
Fa0/0       1   100  P Standby   192.168.0.1     local   192.168.0.254

All the HSRP configuration from this article can be fine tuned or extended according to your needs. I have presented here only the basics about the HSRP configuration. If you want don’t be afraid to explore and to “play” with the commands. Of course I would recommend to do that in test environment first.

A world without wireless

Funny video about a world in which wireless would not exist. Sometimes I’m also complaining about slow access over wireless, errors or possible security holes, but looking at this material I realized that even with this gaps, this technology is doing a great job. I cannot imagine a world without it.

This video appear in celebration of the recently approved 802.11n standard. Also you can visit Cisco’s website Your Ideas in Motion where you can find white papers that provide an overview of the 802.11n standard, 802.11n competitive performance test results and collaborative testing with Cisco and Intel.

10 Cisco IOS Router file management commands every Cisco admin should know

Well this is the most CIsco IOS basics commands and perhaps useful for some of you, who are beginning to experience with this products.

The following Cisco IOS commands explained in the video below are used for file management:

dir, cd, copy, delete, rm, show flash, erase, format, more, verify, mkdir, fsck

The tutorial is work of Bill Detwiler at TechRepublic.com.

Cisco: 2-Bytes / 4-Bytes ASN BGP scenarios

In my last post I wrote some basics about the new 4-bytes AS number which is supported on new Cisco IOS images. Now I would like to give you a brief overview about different BGP peering scenarios that you can meet in the real world. Even if the configuration examples in this article are on a Cisco hardware with the latest IOS, the BGP scenarios can be applied to any other platform.

OK, let take the following topology (the high quality PDF file can be downloaded here):

2bytesAS-4bytesAS-BGP

You can see that I think of 3 main scenarios when it comes to have in the same topology 2-Bytes only and 4-Bytes ASN BGP routers:
– 2-Bytes support ASN peering with a 4-Bytes ASN, which has a number greater that 65535 (if you remember from the previous article, this can be wrote as ASPLAIN or ASDOT)
– 4-Bytes ASN peering with a router that support 4-Bytes ASN, but in fact has a number smaller than 65535 (e.g old telecom provider which has has the ASN already asigned as 3456)
– 2-Bytes ASN peering with the same 4-Bytes supported ASN, but with a number smaller than 65535, as in the above scenario

I chose this particular scenarios because it will be interesting to see how we configure a 2-Bytes ASN BGP router which has a 4-Bytes ASN peer or how the same 2-Bytes ASN BGP router will have the AS-Path containing the 4-Bytes ASN router.

For the R1 and R3 routers I will use a C3640 with an IOS image that support only 2-Bytes ASN, and for R2 and R3 a C7200 with the newest IOS image that can support 4-Bytes ASN. All routers have a Loopback interface that will be the BGP router-id an also announced into BGP (e.g. R2 will have interface Loopback100 with IP address 2.2.2.2/32). The AS number that I will use (ignore the fact that I use public ones, it’s just to be more easy to follow):

R1 – ASN 1111
R2 – ASN 2.2 (ASPLAIN 131074)
R3 – ASN 3333
R4 – ASN 4444

I will skip all the boring point-2-point configuration and present only the BGP config.

#### R1-C3600 ####

router bgp 1111
bgp router-id 1.1.1.1
neighbor 10.10.12.2 remote-as 23456
network 1.1.1.1 mask 255.255.255.255

As you can see in BGP peering between R1 and R2 we have to use the remote-as number 23456, due to the fact that R1 is not supporting 4-Bytes ASN. If you read my previous post, or from other sources, you know that any BGP router that does not support 4-Bytes ASN, will use a transitory number for peering with 4-Bytes ASN BGP routers and this number is 23456.

#### R2-C7200 ####

First let’s be sure that the IOS is supporting 4-Bytes ASN. Simplest way:

router bgp ?
<1-65535>    Autonomous system number
<1.0-XX.YY>  4 Octets Autonomous system number

I think it’s obvious that it supports. A small note. On all Cisco platforms (usually C3600, C7200) with IOS that I tried testing 4-Bytes ASN BGP, I saw that only ASDOT format is supported. I don’t know about other software platforms (like NX-OS) or something high-end hardware if they support ASPLAIN. Now for the configuration, R2 is peering with R1 and R3:

router bgp 2.2
bgp router-id 2.2.2.2
neighbor 10.10.12.1 remote-as 1111
neighbor 10.10.23.3 remote-as 3333
network 2.2.2.2 mask 255.255.255.255

#### R3-C7200 ####

R3 supports 4-Bytes ASN, but due to the fact that it’s and “old telecom provider” it had been assigned a 2-Bytes ASN, so I will preserve this form:

router bgp 3333
bgp router-id 3.3.3.3
neighbor 10.10.23.2 remote-as 2.2
neighbor 10.10.34.4 remote-as 4444
network 3.3.3.3 mask 255.255.255.255

The difference between R3 and R1 is that R3 support for “remote-as” a 4-bytes ASN number (again only ASDOT representation). So, in it’s peering with R2, the remote ASN is 2.2

#### R4-C3600 ####

R4 only support 2-Bytes ASN, but the difference from R1 is that it has to peer with a 4-Bytes supported ASN router that in fact has a 2-Bytes AS number.

router bgp 4444
bgp router-id 4.4.4.4
neighbor 10.10.34.3 remote-as 3333
network 4.4.4.4 mask 255.255.255.255

This is the basic configuration in this topology. Let’s take now the IP address 1.1.1.1 which is advertised into BGP from R1. If you will check the AS-Path on R4 and R3, you will see a big difference. Have a look into the screen capture below to see the real environment for the above topology:

2b4b-bgp