How to use a Cisco router as Frame-Relay switch


For this tutorial you can use  a low cost Cisco router and of course you need some serial interfaces available on this router. I will use a 7206 with 3 serial interfaces. This router I will call R6 and the rest of the three routers connected to R6, will be R2, R5 and R9. In this way it will be easier for you to understand how the frame-relay routing is achieved.

If we have a look to R6’s (the router used as frame-relay switch) interfaces:

r6-c7206#sh int desc
Interface                      Status         Protocol       Description
Fa0/0                            up                down
Fa0/1                             up                down
Se5/0:1                         up                up                    TO_R2
Se5/1:2                         up                up                    TO_R5
Se6/0                            down          down
Se6/1                             up                up                    TO_R9

you’ll notice that we have 3 active serial interfaces, each being connected to one of the three routers R2, R5 and R9.

Very important, before you begin define a scalable range for your DLCI numbers, otherwise you will have a complete mess when troubleshooting is needed. I like to define them after formula Rx0Ry. In the middle you have the number zero. In this idea, we will have something like R20R5 and from this resul the DLCI 205 for the Frame-Relay connection between R2 and R5. Below you have the DLCI numbers used in this tutorial:

R2 -> R5: DLCI 205
R2 -> R9: DLCI 209
R5 -> R2: DLCI 502
R5 -> R9: DLCI 509
R9 -> R2: DLCI 902
R9 -> R5: DLCI 905

Now that we have defined the DLCI numbers lets configure R6 router as frame-relay switch.

First of all, you need to enable frame relay switching on the router:

r6-c7206#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
r6-c7206(config)#frame-relay switching

This command enable the switching  of packets based on the data?link connection identifier (DLCI) inside your router.

Next, we have to configure the frame-relay routing on the physical interface. We will start with interface S5/0:1 where R2 router is connected and apply the following configuration

interface Serial5/0:1
description TO_R2
no ip address
encapsulation frame-relay
! the frame-relay switch is the DCE and the other end is the DTE
frame-relay intf-type dce
frame-relay route 205 interface Serial5/1:2 502
frame-relay route 209 interface Serial6/1 902

With frame-relay route command we tell to frame-relay switch where to forward the packets based on the DLCI number. If we take a look to the first frame-relay route command, than the path to DLCI 502 is interface Serial5/1:2. If you feel confuse, please check again above the interface connection to the router and the assigment scheme for DLCI numbers.

The same like for interface S5/0:1, we will configure the interfaces connected to R5 and R9:

interface Serial5/1:2
description TO_R5
no ip address
encapsulation frame-relay
frame-relay intf-type dce
frame-relay route 502 interface Serial5/0:1 205
frame-relay route 509 interface Serial6/1 905

interface Serial6/1
description TO_R9
no ip address
encapsulation frame-relay
frame-relay intf-type dce
frame-relay route 902 interface Serial5/0:1 209
frame-relay route 905 interface Serial5/1:2 509

Having a look to S5/1:2, first frame-relay route command, here we configure the path back from R5 to R2, by telling the frame-relay switch to chose interface S5/0:1 to send packets to DLCI 205 (R2).

This is the basics of how to configure a Cisco router as a frame-relay switch. If you need help, please don’t hesitate to use the comment form below.

Frame-Relay: PVC test with ping to own interface

Let’s say that you have a link configured with Frame-Relay and from time to time you observe that the link is having some strange problems. Since you cannot be sure that the link is provided 100% error free you want to do your own tests. You want to see if the Frame-Relay between R0 and R1 is correctly configured. In order to verify this you want to set up the R0 to test the PVC to R1, by sending traffic to its own IP address.

Please download the topology here. The Frame-Relay between R0 and R1 is already configured.

See the tutorial below: