Tag: cisco

Cisco: How to configure HSRP

In this post I proposed to discuss a little bit about Hot Standby Router Protocol and how it can be configured on a Cisco device. For this I have chosen the following topology:

cisco-configure-hsrp

I had in mind this scenario due to the fact that the traffic can take multiple paths in case of link being down and this give us the possibility to have a little bit of conversation on HSRP topic.
HSRP is defined in the document RFC2281 and according to the definition in this document: “The Hot Standby Router Protocol, HSRP, provides a mechanism which is designed to support non-disruptive failover of IP traffic in certain circumstances.” If you want to read more about the details how HSRP is working, please the RFC2281. I think there is not point in reproducing here what is already written there.
Regarding our topology, what you should know is that after configuring HSRP on R1 and R2 we will achieve a failover mechanism for the traffic from the Client (192.168.0.10) to the Server(10.10.10.10). From the beginning we will assume that R1 and R2 have the proper routing already configured to reach this destinations.

In the below presentation, you will see how the failover is achieved and what’s happening when you have a proper HSRP configuration in case that the link SC – R1 is broken:

So, how to achieve this behavior? From the topology you notice that proper configuration of HSRP involves 3 IP addresses from the same subnet (in our case this is 192.168.0.0 /24). One of the IP is configured on R1 the second one on R2 and the third one is HSRP IP address, which will be announced to the Client as gateway.

Configuration is straight forward on R1:

configure terminal
interface fa0/0
ip address 192.168.0.1 255.255.255.0
standby 1 ip 192.168.0.254
standby 1 priority 110

and on R2:

configure terminal
interface fa0/0
ip address 192.168.0.2 255.255.255.0
standby 1 ip 192.168.0.254

First we configure an IP address on the interface. Then we configure HSRP by typing the command “standby” followed by HSRP group (in our case group 1) and then the IP address. HSRP default priority is 100, and the principle is the higher the better. To force the path R1-SC to be the preferred one, we increse the priority to 110, making R1 to be the “Active” one. The other router, in our case R2, will have the HSRP status “Standby“. Maybe you are wondering what happens if you don’t configure the priority and both routers are having the same value 100. In this case HSRP has a mechanism that help it to chose the active router by comparing the IP addresses and chosing the one with the higher value. In our case this would be R2 (192.168.0.2 > 192.168.0.1).
Another useful feature that I recommend to configure for HSRP is “preemption“. The HSRP preemption feature enables the router with highest priority to immediately become the Active router. The configuration is also very simple and inquire only one additional line to the above ones:

standby 1 preempt

Also recommended is to configure “authentication“ between the HSRP participants:

standby 1 authentication somepassword

where “somepassword” can be what ever you want.

Going back to the topology, another scenario can take place. What if the link R1 – SC remains active, and instead the R1 – SS goes down. Since the R1 – SC is UP, the router R1 has no intention to cease the HSRP Active status. If you are having some kind of dynamic routing between R1 and R2, then you are on the safe side as the traffic will flow like in the scenario below (I’m assuming R1 to be the Active one for both R1-SC and R1-SS):

Remember that if do not have some routing between R1 and R2, the packets will be dropped on R1 as they will not have any path to the Server IP address 10.10.10.10.

This situation can be avoid with another HSRP feature, that will force the R1 to change it’s status from Active to Standby by monitoring the interface from R1 to SS. This feature is called “interface tracking“. This HSRP feature you have to configure at least on the router which is usual in Active mode:

standby 1 track FastEthernet1/0 30

In this scenario I assume that interface Fa1/0 is the connection to SS switch. This tracking command is watching for the status on the interface Fa1/0. When it’s status changes to “down” the “priority” value (110 in this example) is decremented with 30 (or whatever you will configure in the command line). After decremental, the “priority”
will have a value of 80 which is lower than the default one (100), forcing R2 to become the Active router and changing the R1 status to Standby.

Checking the status of an HSRP participant is very easy, and you can see this in the output below:

R1#show standby brief
P indicates configured to preempt.
|
Interface   Grp Prio P State    Active          Standby         Virtual IP
Fa0/0       1   110  P Active   local           192.168.0.2   192.168.0.254

R2#show standby brief
P indicates configured to preempt.
|
Interface   Grp Prio P State    Active          Standby         Virtual IP
Fa0/0       1   100  P Standby   192.168.0.1     local   192.168.0.254

All the HSRP configuration from this article can be fine tuned or extended according to your needs. I have presented here only the basics about the HSRP configuration. If you want don’t be afraid to explore and to “play” with the commands. Of course I would recommend to do that in test environment first.

Posted on by Calin 3

A world without wireless

Funny video about a world in which wireless would not exist. Sometimes I’m also complaining about slow access over wireless, errors or possible security holes, but looking at this material I realized that even with this gaps, this technology is doing a great job. I cannot imagine a world without it.

This video appear in celebration of the recently approved 802.11n standard. Also you can visit Cisco’s website Your Ideas in Motion where you can find white papers that provide an overview of the 802.11n standard, 802.11n competitive performance test results and collaborative testing with Cisco and Intel.

Posted on by Calin 0

10 Cisco IOS Router file management commands every Cisco admin should know

Well this is the most CIsco IOS basics commands and perhaps useful for some of you, who are beginning to experience with this products.

The following Cisco IOS commands explained in the video below are used for file management:

dir, cd, copy, delete, rm, show flash, erase, format, more, verify, mkdir, fsck

The tutorial is work of Bill Detwiler at TechRepublic.com.

Posted on by Calin 2

Cisco Metro Ethernet 6524 Switch

Posted on by Calin 0

4-bytes Autonomous System Number

Last week I received a form from APNIC with a new AS numbers. When I had a look through papers I saw there something strange: AS 123456 (I replaced the original with this number). 6 digits. First I thought that there is a mistake or something, then I recall the new 4-bytes ASN. If for IPv6 the things seems to be moving slower, than for the new format of AS numbers, it seems that the things are going faster. So faster that by January 1, 2010 all BGP speaker must support this feature, according to Cisco. I didn’t understood if they refer in the document for their products or it is something that is mandatory globally. No matter how, the things are moving quite fast in this direction.

Since I have to implement a BGP configuration with this 4-Bytes ASN, I started to search with Google friend about the standards and I was surprised that there is not to much to search after. Of course there is the official RFC, some other documentation, but not real examples how to configure, troubleshoot and so on. That’s why I said it’s nice to put something together for a general understanding of what is and how does it work this 4-Bytes ASN. I assume here that reader has a basic understanding of what ASN and BGP is.

RFC 4893 is the reference for “BGP Support for Four-octet AS Number Space”. Currently the Autonomous System number is encoded as a two-octet (2-bytes) entity in BGP, meaning 16bits and this was defined in RFC 4271. The new system is using a four-octet (4-bytes) , meaning 32bits. Currently the ASN 2-bytes include a range from 1 – 65535, used in decimal plain text when configuring the BGP. The expansion from 2-bytes to 4-bytes give us 4,294,967,295 AS number which can be written in ASPLAIN or ASDOT format.

Why two formats? Mainly due to different opinions about how the 4-bytes number should be represented:

ASPLAIN representation

The RIPE NCC assigns and registers 4-byte AS Numbers in ASPLAIN format.
ASPLAIN defines the 4-byte AS Number as a basic 32-bit integer.
“2-byte only AS Numbers” refers to AS Numbers in the range 0 – 65535
“4-byte only AS Numbers” refers to AS Numbers in the range 65536 – 4294967295”
“4-byte AS Numbers” refers to AS Numbers in the range 0 – 4294967295
Advantages:
– IETF preferred notation
– continuation on how a 2-Byte AS number has been represented historically
– does not break AS-PATH REGEX
– APNIC reached consensus to adopt ASPLAIN for assignment and representation of 4-byte AS Numbers
– routers vendors appear to be supporting ASPLAIN, which will require no conversion from allocation to configuration
Disadvantages:
– long number to remember
– All existing 4-byte only assignments have been made in ASDOT

ASDOT representation

The full binary 4-byte AS number is split two words of 16 bits each. It is proposed to identify 4-byte AS Numbers using a syntax of <high
order 16 bit value in decimal>.<low order 16 bit value in decimal>:
“2-byte only AS Numbers” refers to AS Numbers in the range 0 – 65535
”4-byte only AS Numbers” refers to AS Numbers in the range 1.0 – 65535.65535
“4-byte AS Numbers” refers to AS Numbers in the range 0.0 – 65535.65535
Advantages:
– easy to read and remember
Disadvantages
-require conversion from ASPLAIN to ASDOT
-hard for regular expressions

What’s happening if in a BGP peering one router supports the new format and the other one only the old one.  The new reserved ASN 23456 is used for backward compatibility between 4-bytes and 2-bytes BGP speakers. So, if your router advertise BGP with a 4-bytes as number (doesn’t matter in which representation ASDOT or ASPLAN), the peer which does not support the new format, will translate the 4-bytes ASN into 2-bytes ASN 23456. A graphical representation of the AS path from 4-bytes to 2-bytes in BGP would be:
4bytes-2bytes-as

OK, I hope you understand the basics of 4-bytes ASN. For me, some challenge was to understand to transform the 4-bytes ASN from ASPLAIN to ASDOT. In every document that I saw on the Internet there was the same example: AS 65546 in ASPLAIN is 1.10 in ASDOT, but without no explanation. See below how I understood that the conversion takes place. If I understood it wrong, please let me know, to correct it here. After all I’m not an 4-byte ASN expert, I just try to help as much as I can.

So let’s take the number 65546.

1. 65546 / 65535 = 1 (integer) which will be the parte in front of the . (dot) in ASDOT representation.

2. 65546 – ( 65535 * 1) = 11 (see how much rest remains after 65353 going once in 65546)

3. 11 – 1 = 10 which will be the part after . (dot)

4. You obtain 1.10

As a general rule, you have an ASPLAIN number. You take 65535 and see how many times it goes, with integer in the ASPLAIN number (1 time, 2 times, 3 times…depending). This will be your decimal number before dot in ASDOT format . Then you multiple the 65535 with the integer obtained in the first step and you deduct from the ASPLAIN number. From the rest after the second operation, you deduct the the decimal you have in front of the dot. The rest in decimal that comes after the dot .

What confused me is that the number in the example was so close to the last 2-bytes ASN which is 65535.

Now for the last example, let me take a random higher number 194534 (the example from the first line) and to obtain the ASDOT format.

1. 194534 / 65535 = 2 (integer)

2 194534 – ( 65535 * 2) = 194534 – 131070 = 63464

3 63464 – 2 = 63462

4 ASDOT = 2.63462

An online converter from ASPLAIN do ASDOT you can find here: http://as4.nullroute.se/index.php

For some more detailed explanation I would like to ask you to download the Cisco and Juniper documents regarding 4-bytes ASN implementation in BGP.

If you have any useful information about this topic or if something is wrong in my post, please comment and share your knowledge.

Posted on by Calin 5